Search Results (5.6K)
Conversation Type :
Posts
Published Date :
Lifetime
Category
Community Accepted Solution
I have added an additional physical disk my PowerEdge 650 server.After the disk was ready i logged into the IDRAC and added it to the existing raid and started the reconstruction which took about 24 hours to complete fully.The drive is now showing to be part of the raid 5 and the size of the raid on
Question
•
PowerEdge HDD/SCSI/RAID
Community Accepted Solution
Hi . Same problem on my server. ı m confused then ı had angry. Could you help me this problem :) When i firmware update on F10 Lifecyle . That is seen this error SWC0066. My internet is normal. Modem rule is normal. ı have no Firewall and switch . I did NVRAM clear . check other compenent bu
Question
•
Rack Servers
Community Accepted Solution
Hi all, I have a Dell R730 with 2 x Xeon E5-2673v4 (20 core), 256 GB RAM, 16 x 2.5" Crucial 2TB SSD configured as a RAID-10 with a H730 Perc controller. On this device are 20 VMs, each configured with 8GB of RAM and 4 vCPU. A couple of the users logging in via RDP are saying that the response time
Question
•
PowerEdge Hardware General
Community Accepted Solution
Hi~ Is there any plan to support Xen server with perc 12?
Question
•
PowerEdge HDD/SCSI/RAID
Community Accepted Solution
Hi all, Does someone know the part number of this piece? Poweredge R340 right ear Thanks in advance,
Question
•
PowerEdge Hardware General
Community Accepted Solution
I have a Dell R740 with the Ethernet 10G 4P X520/I350 rNDC Card installed. If i use the old firmware update file for 22.0.9 Release, the NVM Update Tool finds the card and would update the firmware. Num Description
Question
•
Rack Servers
Community Accepted Solution
Hello, I am trying to monitor the CPU utilization for the PowerEdge FN 410S IOM via SNMP. Does anyone know the OID for this sensor or if it is possible to query? Thank you, Matthew
Question
•
PowerEdge HDD/SCSI/RAID
Community Accepted Solution
Hello, how can I wipe the hard drive for a M610. I can go back to defaults with the IRDAC and Bios, but I cannot seem to find a way to wipe the hard drive on the unit. I do not see a Retire or repurpose option in the Lifecycle setup
Question
•
PowerEdge Hardware General
Community Accepted Solution
Hi I want to upgrade my server PowerEdge R730 second processor What equipment needed? Please advise
Question
•
PowerEdge Hardware General
Community Accepted Solution
Hello, hope everyone is doing well. Question - If I want to install 2 GPUs in a PowerEdge R940XA server, then would I just need the 16x risers and respective cables? Is there a part number for a GPU Enablement Kit? Thank you
Question
•
PowerEdge Hardware General
Community Accepted Solution
Kind of using this as a last resource as I cannot seem to fix this on my own. I have a new to me PowerEdge 2970 (yes I know the server is well past support and should absolutely be replaced by today's standards; however, it is only used for home/remote storage and it fits my needs perfectly for what
Question
•
Rack Servers
Community Accepted Solution
I am unable to find any compatibility list for the PowerEdge R760sx, can someone tell me if it is compatible with the Intel x520 line? If not, what are the suggested cards for this system and CentOS 7? Thanks!
Question
•
PowerEdge Hardware General
Community Accepted Solution
Hello! I failed finding information on the Dell U.2 enablement kit P31H2 so I am asking here. Does this card absolutely have to be installed in an x16 PCIe Slot or will it work at a x8 as well (with reduced max. speed)? What does the card do exactly? Splitting 16 lanes into 4x4 with bifurcation s
Question
•
Rack Servers
Community Accepted Solution
Hi All,I have an old T320 which is having the below Issues, Just trying to confirm whether it might be a board issue -No Display on Embedded VGA or Graphics card -No Post (Even with Minimum Requirements for Post) -No Beeping when ram removed -CPU Internal Error - Constantly Power cycles on and off
Question
•
PowerEdge Hardware General
Community Accepted Solution
Keep getting full and predictive failures on a specific drive in a RAID6 array, on r730. What is the best drop-in replacement? (Exact same or equivalent Dell part?) Would any ST6000NM0095 do, or does it have to be a Dell PN? Would any (Dell or non-Dell) drive work as long as it's the same capaci
Question
•
Rack Servers
Community Accepted Solution
I need firmware hdd s/n wmayp7582326 Wwn:50014ee0ae6a5d9a P/n: 01kwkj Firmware' 1s03 Mdl: wd5003abyx-18wera0 Dcm hgrnthtjcg Dcx:_ 8e02e76r2 R/n: 771702 Please need firmware my data lost thanks dell team
Question
•
PowerEdge HDD/SCSI/RAID
Community Accepted Solution
I have a Power Edge R440 In Open manage under Storage/perc H730P adapter (Embedded)/Connector 0 (RAID)/Enclosure (Backplane)/Physical Disks. I see 5 drives, 2446.62GB i believe to be a mirrored C drive. and 3 893.75 GB drives i expect to be the RAID 5 for D: They are all showing good, but i need to
Question
•
PowerEdge Hardware General
Community Accepted Solution
Hello! I'm a complete noob to this so please excuse my lack of knowledge. I'm looking for some help with this. I bought a used R730, and am currently configuring it. The hard disks I have are 4 new 1.2 TB SAS Hard Drives (Dell WXPCX). I'm trying to set up RAID 6 on it, and then will be installing
Question
•
PowerEdge HDD/SCSI/RAID
Community Accepted Solution
Hi, My Dell T640 does not turn on, it has 2 power supplies connected, but when I press the power button, it does not start and the LEDs on the motherboard show the following status: DS0 - OFF DS1 - ON DS2 - OFF DS3 - OFF DS4 - OFF DS5 - BLINK DS6 - BLINK Any idea about it.? Thank's a lot.
Question
•
PowerEdge Hardware General
Community Accepted Solution
The powersupply is mentioned with 100-240V 50/60Hz for AC input OR 240V for DC input. This means we can connect 110V AC or 230V AC. However for DC is it only 240V DC, can't we use 120V DC ?? Why the range of DC is not mentioned as like in AC.
Question
•
PowerEdge Hardware General