Dell Client Configuration Toolkit (CCTK) Error Codes - Systems Management - Wiki - Systems Management - Dell Community
Wikis - Title

Dell Client Configuration Toolkit (CCTK) Error Codes

Systems Management

Systems Management
Dell Systems Management Solutions: Dell OpenManage, iDRAC, Repository Manager, Microsoft SCCM, Chassis Managment Controller, and more

Systems Management - Wiki

Dell Client Configuration Toolkit (CCTK) Error Codes

Systems Management - Wiki

CCTK error codes as of version 2.2.1.

0. Success.

1. Attempt to read write-only parameter '%s'.

2. Password cannot exceed 16 characters.

3. A BMC was either not detected or is not supported.

4. This username is already in use. Enter a unique username.

5. Access mode not supported.

6. Cannot return number of requested data bytes.

7. User ID 1 cannot be assigned a username.

8. Cannot execute duplicated request.

9. There was an error clearing the SEL.

10. Clear SEL cannot be accompanied with any other option.

11. racreset cannot be accompanied with any other option.

12. Cannot execute command '%s'. Command, or request parameter(s), not supported in present state.

13. Command not supported on given channel.

14. The community string may only contain printable ASCII characters.

15. Destination unavailable. Cannot deliver request to selected destination.

16. Cannot execute command. Insufficient privilege level.

17. Command illegal for specified sensor or record type.

18. Invalid commstring value.

19. Hardware subsystem error. Invalid data field in Request.

20. Invalid destination IP address.

21. The GUID is invalid.

22. Invalid gateway.

23. Invalid hostname.

24. Invalid IP address.

25. Invalid DNS IP address.

26. Invalid sub net mask.
27. Invalid value for PEF. PEF value should be between 1 and 16.

28. Reservation Canceled or Invalid Reservation ID.

29. Invalid Time to live value.

30. Invalid VLANID value.

31. Invalid Command. Used to indicate an unrecognized or unsupported command.

32. Command invalid for given LUN.

33. Load defaults cannot be accompanied with any other option.

34. There was an error loading the defaults.

35. Node Busy. Command could not be processed because command processing resources are temporarily unavailable.

36. Out of space. Command could not be completed because of a lack of storage space required to execute the given command operation.

37. This parameter is not supported.

38. Parameter out of range. One or more parameters in the data field of the Request are out of range.

39. The password may only contain printable ASCII characters.

40. Password test failed.

41. Requested data length invalid.

42. Requested data field length limit exceeded.

43. Requested Sensor, data, or record not present.

44. Request data truncated.

45. Command response could not be provided.

46. Command response could not be provided. BMC initialization or initialization agent in progress.

47. Command response could not be provided. Device in firmware update mode.

48. Command response could not be provided. SDR Repository in update mode.

49. Cannot execute command, SEL erase in progress.

50. Attempt to set the 'set in progress' value when not in the 'set in complete' state.

51. The SOL character 'accumulate interval' is invalid.

52. The SOL character 'send threshold' is invalid.

53. The SOL 'retry interval' is invalid.

54. Command completed successfully.

55. Timeout while processing command. Response unavailable.

56. Unspecified error.

57. The password may only contain printable ASCII characters.

58. Username cannot exceed 16 characters.

59. Invalid VLANID value. Enter in 'dddd' format.

60. Attempt to write read-only parameter '%s'.

61. BMC is busy.

62. Response data did not return successfully.

63. BMC time out error.

64. Invalid Configuration Option.

65. Cannot execute command.Parameter is illegal because command sub-function has been disabled or is unavailable.

66. Option '%s' requires an argument.

67. The asset tag for this system is not available.

68. The asset tag cannot be more than 10 characters long.

69. The required BIOS interfaces cannot be found on this system.

70. The BIOS version information is not available.

71. There is not enough free system memory to complete the BIOS update.

72. The BIOS update file version is a different version class (A00, X00) than the current system BIOS. Use the --force option to use this BIOS image.

73. The BIOS update file version is older than the current system bios. Use the --force option to use this BIOS image.

74. The BIOS update file version is identical to the current system bios. Use the --force option to use this BIOS image.

75. The sequence list must be a comma-separated numerical list of valid unique boot device numbers (ex: 2, 1, 3).

76. The sequence list must be a comma-separated list of valid unique device names (ex: nic.emb.1, hdd.emb.1) or a comma-separated numerical list of valid unique boot device numbers (ex: 2, 1, 3).

77. There was an error setting the sequence.

78. The list is not formatted correctly. See the help for more details.

79. The size of returned buffer is larger than the size of allocated buffer.

80. There was a problem getting the state byte.

81. The state byte is not available on this system.

82. There was a problem setting the state byte.

83. The state byte must be a value between 0 and 255 decimal.

84. The CPU information is not available.

85. The dependent option '%s' required for this subcommand is missing in the command line.

86. Duplicate sub command '%s' has been entered.

87. The script file does contain not a valid DTK environment script signature. (%s)

88. The format of the environment variable is incorrect.

89. The --envar/-s option can only be used for a single option.

90. The --envar/-s option can only be used for report operations.

91. The individual sub commands should be specified for the -s option.

92. Getting external serial connector settings failed.

93. Setting external serial connector settings failed.

94. There was an error opening the file %s.

95. File '%s' does not have write permission.

96. The file contains invalid option '%s'.

97. The replication information does not match for this system.

98. There can only be one section in the input file.

99. Bad ini file, the required section [%s] cannot be found.

100. The format of the bios image file is incorrect.

101. Report operations and set operations must be separate.

102. Help is not available for the option '%s'.

103. The -x (--hex) option can only be used with -b or -r.

104. Input file '%s' not found.

105. Input file '%s' cannot be read.

106. Invalid argument for the provided option '%s'.

107. Function table lookup error.

108. The machine ID was not found in the file '%s'.

109. The system memory information is not available.

110. Mode can only be used with the --pci option.

111. The device name or index must be present in the boot order.

112. The output file '%s' could not be opened. Please make sure the path exists and the media is not write protected.

113. Could not write to output file, disk may be full.

114. The old password must be supplied to set a new password using --valsyspwd.

115. The old password must be supplied to set a new password using --valsetuppwd.

116. The current password can only be supplied when setting a new password.

117. Actions are not allowed for this filter. Only alerts are allowed.

118. There was an error getting the option '%s'.

119. The option '%s' is not available or cannot be configured through this tool.

120. There was an error setting the option '%s'.

121. The -n (--namefile) option can only be used with --pci.

122. The password may only contain alphanumeric characters.

123. The BIOS passwords have been disabled via jumper.

124. The password length must be between 1 and 32.

125. This password is locked and can only be unlocked by the admin user.

126. There was an error setting the password.

127. The LCD string length must be between 1 and the maximum value %s.

128. The LCD string may only contain alphanumeric characters.

129. There was an error setting the LCD string.

130. The second channel can only be set if the RAID controller is set to RAID.

131. The set operation, '%s', requires sub commands.

132. The service tag for this system is not available.

133. The system ID value is not available.

134. The system information string is not available.

135. A system error has occured.

136. Usage error.

137. The uuid information is not present on this system.

138. The manufacturing/first-power-on date information is not present on this system.

139. Version cannot be accompanied with any other option.

140. The self-identify blinker timer should be set to 0..255 second(s).

141. Encrypt key is too long.

142. Encrypt key is invalid, accepted characters are 0 to 9 or A to F.

143. Parameter has been temporarily disabled due to a dependancy on other settings.

144. The old password supplied is incorrect. The new password will not be set. Please try again.

145. Cannot start /etc/omreg.cfg file. Please ensure /etc/omreg.cfg file is present and is valid for your environment. You can copy this file from the DTK iso.

146. Getting nicselection settings failed.

147. HAPI Driver Load Error.

148. Filter action power reduction is only supported for the system power warn/fail filters.

149. TPM Clear settings requires setup password.

150. There is currently no TPM Clear request pending.

151. Password is not required for retrieving the TPM options.

152. Setup password is required for setting the TPM options.

153. Invalid Password override.

154. Invalid TPM set option.

155. There was an error setting the TPM option.

156. There is no setup password installed on this system.

157. The setup password supplied is incorrect. Please try again.

158. Profile should be custom for setting cpupowermode, memorypowermode and fanmode.

159. There was an error setting the Power Option.

160. The power cap value entered is out of range. Please try again.

161. The power cap value entered must be between 0 to 100 if unit is percent.

162. Invalid IPv6 address. The IPv6 address cannot be link-local or multicast.

163. Invalid IPv6 address. The IPv6 address specified has incorrect address format.

164. Invalid IPv6 address. The gateway address specified has incorrect address format.

165. Invalid IPv6 address. The Primary DNS server address specified has incorrect address format.

166. Invalid IPv6 address. The Secondary DNS server address specified has incorrect address format.

167. Invalid IPv6 address. The gateway address specified is invalid.

168. Invalid configuration. Attempting to apply IPv6 configuration on a non supported platform.

169. Invalid IPv6 configuration. Attempt to set DNS server address manually while DNS address source is set to auto.

170. Invalid IPv6 configuration. Attempt to set IPv6 address manually while IPv6 address source is set to auto.

171. Invalid IPv6 configuration. Attempting to apply IPv6 configuration without loading IPv6 stack.

172. Invalid IPv4 configuration. Attempting to apply IPv4 configuration with IPv4 disabled.

173. Invalid IPv6 configuration. Ipv6 address cannot be specified without specifying prefix-length.

174. Invalid IPv6 configuration. dnssrcv6 cannot be set to auto when ipsrcv6 is set to manual.

175. Error while executing IPMI Set command.

176. Error while executing IPMI Get command.

177. Error during Trap Alert.

178. Unspecified error.

179. Unsupported device. Re-try with supported device

180. Setup password is installed. Re-try providing setup/admin password

181. System password is required. Re-try providing system password

182. The password supplied is incorrect. Please try again.

183. Password verification failed.

184. Password not changed, new password does not meet criteria.

185. Password not installed in the system.

186. Password is DISABLED by jumper.

187. Error in Validation.

188. Error in Setting the Value.

189. The password length should not exceed the maximum value %s.

190. This is not a Dell machine. CCTK supports only Dell machines.

191. Setup Password is required to change the setting. Use --valsetuppwd to provide password.

192. System Password is required to change the setting. Use --valsyspwd to provide password.

193. Password is not Installed. so use only --setuppwd

194. Password is not Installed. so use only --syspwd

195. The system password supplied is incorrect. Please try again.

196. The Sequence list must be a comma-separated list of valid unique device names (ex: hdd,cdrom).

197. The system revision information is not available for this system.

198. The completion code information is not available for this system.

199. The BIOS characteristics information is not available for this system.

200. The password should not contain special characters. Password characters are limited to alphanumeric (A-Z, a-z, 0-9).

201. Please use 64-bit version of this application.

202. %s cannot be modified when TPM is OFF.

203. System password cannot be set when pwdlock option is in locked state (pwdlock=lock).

204. adddevice option not supported by this machine's BIOS

205. usb device already present in this machine.

206. Unable to get information from BIOS.

207. %s - Error : Unable to store BIOS information.

208. Duplicate entry found in the input list : %s , Operation Aborted.

209. Typo found in the input list : %s , Operation Aborted.

210. Asset tag can have only printable ASCII characters.

211. Multiple inputs will not be accepted.

212. Invalid Hex format.

213. Hex value range should be 0x0 to 0xffff.

214. %s - Only positive numeric values are acceptable.

215. %s - Length cannot exceed two characters.

216. Range for autoon hour value should be 0 to 23(24 hour format).

217. Range for autoon minute value should be 0 to 59.

218. This option Not supported on UEFI Bios.

219. Unable to Set Bootorder.

220. Invalid Arguments. Unable to Set Bootorder.

221. The provided command %s should not combine with other suboptions.

222. The property ownership tag for this system is not available.

223. The property ownership tag cannot be more than 80 characters for non portable machines.

224. The property ownership tag is limited to 48 characters for portable systems.

225. Property ownership tag can have only printable ASCII characters.

226. Error in Setting the Value. Note : In some machines, If Hdd password or System password is set, you can't set Setup password.

227. 'admin/root' privileges required to execute this application.

228. The option related BIOS information is not available in this machine.

229. Improper Output from Bios. Please try again.

230. ;Error in Bootorder.

231. The manufacturing/first-power-on date information is not present on this system.

232. Not Applicable.

233. ;Uefi bootlisttype is not supported in this Machine.

234. Improper Output from Bios. Please try again.

235. ;Error in Bootorder.

236. Unable to get information specific to machine.

237. The input file is invalid.

238. No Status Present.

239. File Do not have configurable Options.

240. Please provide the days to enable.

241. Password is not Installed. Please try again without providing --val%s

242. Please provide the old password to set the new password using --valownerpwd.

243. The owner password is incorrect. Please try again.

244. Error in setting the value. Note : Setup or system password might be set on the system. Clear the password(s) and try again.

245. Owner password is not supported in file operations.

246. Password operation is not supported on the system.

247. The owner of the system has enabled the Owner Access feature. To set the Bios configuration, create setup or system password.

248. Either the system hardware or the BIOS version does not support the option. To resolve the BIOS version issue, upgrade the BIOS to the latest version.

249. Unable to get password information.

250. Please provide the start and stop values. Example: custom:start-end.

251. The start and stop values should be in the range '%s'.
252. The stop value should be greater than the start value by 5 percentage.

253. The option '%s' is not supported in this machine.

254. Unable to set '%s'. Note: To set this Option Legacy Option rom(legacyorom) should be enable and secureboot should be disable.

255. Unable to set '%s'. Note: To set this Option bootmode(activebootlist) should be uefi and legacy option rom (legacyorom) should be disable.

256. Unable to set '%s'. Note: To enable this Option secureboot should be disable. To disable this Option secureboot should be disable and bootmode(activebootlist) should be uefi.
257. The allowed value for the option in the system are in between %s.

258. The option '%s' is not enabled.

259. Invalid argument. The possible values are: onboard, 1-15 (Slot number of primary video device), and auto.

260. Invalid argument. The arguments must be set in such a way that [Start time] less than or equal [End time] less than or equal [Charge Start time].

261. Unable to set the Non critical Threshold values

262. Error in Setting the Value. Note: To set TPM - 1. Admin Password must be set , 2. TPM must not be owned and 3. TPM must be deactivated.

0
Comments
  • Hi. Please add the new errorcodes for CommandConfigure v3.2, getting error 264 as an example