Browse by Tags

Networking

Networking
Learn how to modernize & transform the network with the latest solutions from Dell Data Center, Campus and Wireless networking solutions.
Results for switch
  • Switching between the Stack Master and the Master Backup

    HI Guys, i need just an explication about the Operation of the mode of PowerConnect 5524 Switch... i have 2 PowerConnect 5524 Switchs connected by HDMI cable.. The first unit is a Stack Master and the Second is a Backup Master. i find in the user Guide " Switching between the Stack Master...
  • Dell-8132-Switch-routing

    Dell-8132-Switch-routing Dell Sonic Wall Default gateway :192.168.0.254 Dell 8132 Switch * 2 stacking vlan 1 : 192.168.0.0/24 (Default VLAN) vlan 10 : 192.168.10.0/24 vlan 20 : 192.168.20.0/24 vlan 1 SVI : 192.168.0.250 vlan 10 SVI : 192.168.10.250 vlan 20 SVI : 192.168.20.250 ip routing &...
  • Juniper 4500 SFPs (10g) in a PC8024F

    I have Juniper 4500 SFPs (10g) in a PC8024F and am getting link and show active and up on both sides. Is it possible , with the previous statement , to not pass traffic?
  • change the IP address of a switch 6248 command line

    hello could you tell me how to change the address of my management switch 6248 command line . I connect to the com port and I did enable I type my password and then I do not know the command ? How to see my ip address ? How to change it? Thank you for all your help
  • cisco 2960s

    how about cisco switch 2960s? is it vaildated for ps 4000?
  • Problem with stack of Dell PowerConnect 6224

    Hello. We have a stack of two Dell PowerConnect 6224 connected with 2 stack cables that have been running in production without noticeable problems for almost an year. We recently upgraded them to software version 3.3.2.3 from 3.2.0.7 After the upgrade, we noticed no problem until one strange...
  • Help trunking M6220 to 5524

    I'm having problems bringing up a trunk link between an M6220 blade centre switch and s 5524 switch. We have a largely identical setup in two different racks and I hit the same problem in both. Trunking between 2x 5524 switches works fine but between an M6220 and a 5524 I bring up the ports and LAGs...
  • Power Connect 6224 Vlan Routing Configuration

    Hello people, I am new with Dell switches. I have the following scenario: vlan 10 - 192.168.0.1 /24 vlan 20 - 192.168.1.1/24 FIREWALL - ASA - IP 10.0.0.1 I need to configure routing beetwen this vlans and If the switch receives a packet for a network not in the routing table, it forwards to my Firewall...
  • error message on dell switch

    I am seeing this on the dell logs any ideas; %% Authent. failure:Unit 1: Ip address 192.1.1.1 Thanks
  • PC 6248 L3 Switch Routing to ISP

    And I was wondering if somebody could please help me? We recently sign up for FPL FiberNet Direct Internet Access (DIA), and they provide us with a point-to-point /30 IP for connection between our Fiber-to-copper Transceiver and the NOC and also gave us a block of /28 public IPs that we have to...
  • Routing between PowerConnect 6248P Stack and 8024F

    Hi All, We are about to change our network topology due to some latency issues and wanted some advice on routing between multiple subnets and VLANs across a single 10Gb private ethernet line. We have a stack of PowerConnect 6248P switches with 3 VLANs and the corresponding subnets that we would...
  • NIC Teaming

    I should probably know how to do this, but I'm having trouble finding answers in plain language. I have a PE1950 III with dual NIC's that is acting as a file server. To my surprise, lately, the enabled NIC is running at a constant 70% while machines process data. I'd like to share the load...
  • Networking Section would be great

    The thread subject sort of gets to my point but I'll stress that it would be nice to have a networking section here. The PowerConnect documentation (not the manuals or CLI reference) is not exactly the easiest bit of gear to find help with. The CLI is non-standard enough on these switches that it...
  • VLAN configuration to isolate gateway

    I have not done a lot with VLANs, and I am having a bit of an issue configuring my network correctly. I am hoping someone out there will have a simple solution for me. The WAP I have provides multiple SSIDs and MAC addresses to go with the SSIDs. Each SSID/MAC pair can have a unique zone attached...
  • M1000E with 2 M8024-k switch connected to 6224

    Hi all, I have just buy a Dell M1000E blade chassi with 2 M8024-K switches. Have put in a 10Gb module at both switches and fiber to or 2 old Dell 6224 switches that are stacked at the backside in port1 and have now got a 10Gb module in slot 2. Can see that all swiches can see the 10Gb modules....
  • powerconnect 8100 (namely 8132), is FCoE possible?

    Hello! I can't find any info about this on site, so , could you tell me is there FCoE support in 8100? Thank you!
  • Changing STP mode from MSTP to RSTP on two stacked powerconnect 6224 configured for iSCSI during regular operation

    Hi, I'm about to do a fw upgrade during regular operation on a 6224 stack which currently run MSTP, I am aware of Dells recommendations to run RSTP on switches configured for iSCSI traffic connected to Equallogic SAN. I'm planning to configure another stack with two 6224 in order to failover...
  • Can Dell 2161DS-2 console switches be connected for cascading/tiering?

    I can't get one DS-2 to see another DS-2 connected to it. Have tried connecting an ARI on the top-level (primary) DS-2 via a CAT5 cable to the CAT5 port on the lower (secondary) DS-2, but the primary doesn't detect the connection. I suspect the CAT5 port is not an ACI port, as it is designed...
  • Performance trouble, any troubleshooting advice?

    Hi, We recently made the following changes in our LAN 1) Purchase an L2 connection between our two sites from the ISP 2) Stretched iSCSI VLAN between the two sites for replication Previously our ISP provided a VPN service between the two sites. But since we are improving our DR setup we wanted...