Installing Wireless Network Card Dimension 4700

Networking, Internet, Wireless

Networking, Internet, Wireless
From Wi-Fi to wired Ethernet, mobile broadband to modems: it's all spoken here.

Installing Wireless Network Card Dimension 4700

This question is not answered

Hi,

I have a Dimension 4700 put into service Jan 2005.I removed the side panel and have 2 PCI Express slots open (other 2 are filled with ethernet and IEEE ports) and  I am trying to install a D-Link Wireless Network Adapter that I purchased.  However the adapter doesn't seem to fit in the slot (PCI Express x16 x 1).I was told that the adapter was universal and should be installable. Did I get the wrong adapter,  can it be installed there or do I have to remove the IEEE firewire card and install the adapter there?

 

Thanks

All Replies
  • Universal, as applied to PCI cards, means that they will operate with either 5 volt or 3.3 volt signaling.  The card is a standard PCI rather than PCI-e.  If you must use that card you will need to clear one of the standard PCI slots.

    You could also consider something like this, however:  D-Link DWA-556.  I know nothing about this particular card; I found it while searching for examples of PCI-e cards.  This one is PCI-e X1.  If you look around you may find other examples.  Good luck!

     

    Dell Forum member since 2005

  • Thanks for the quick reply and the link. I will investigate... 

  • X16 Slot is for Video only.

    http://support.dell.com/support/edocs/systems/dim4700/

    http://support.dell.com/support/edocs/systems/dim4700/sm/index.htm

    http://support.dell.com/support/edocs/systems/dim4700/sm/techov.htm#wp1052362

    The Universal card would go into the PCI 2.2/33mhz slots J7B1 or J8B1

    If you have a 4700C thats a totally Different issue.

     

    Expansion Bus

    Bus type

    PCI 2.2
    PCI Express x1 and PCI Express x16

    Bus speed

    PCI: 33 MHz

    PCI Express:

    x1 slot bidirectional speed - 500 MB/s

    x16 slot bidirectional speed - 8 GB/s

     

     

    PCI

     

    connectors

    two

    connector size

    120 pins

    connector data width (maximum)

    32 bits

     

     

    PCI Express

     

    connector

    one PCI Express x1

    connector size

    36 pins

    connector data width (maximum)

    1 PCI Express lane

     

     

    PCI Express

     

    connector

    one PCI Express x16

    connector size

    164 pins

    connector data width (maximum)

    16 PCI Express lanes

    Report Unresolved Customer Service Issues here

    I do not work for Dell. I too am a user.

    The forum is primarily user to user, with Dell employees moderating.

  • 4700C  Has Different Layout.  Universal PCI 2.2 card would not fit there due to needing LOW PROFILE PCIE X1 card.

    http://www.keenzo.com/showproduct.asp?ID=3288142

    Miscellaneous
    Included Accessories   Low-profile bracket

    http://support.dell.com/support/edocs/systems/dim4700c/

    http://support.dell.com/support/edocs/systems/dim4700c/en/SM/index.htm

    Report Unresolved Customer Service Issues here

    I do not work for Dell. I too am a user.

    The forum is primarily user to user, with Dell employees moderating.

  • Removing the firewire card wont hurt anything.

    Just follow proper safety like antistatic protection and unplug from the wall before opening the cover.

     

    Before you open the computer cover, perform the following steps in the sequence indicated.

      CAUTION: Do not attempt to service the computer yourself, except as explained in your online Dell™ documentation or in instructions otherwise provided to you by Dell. Always follow installation and service instructions closely.
    NOTICE: To help avoid possible damage to the system board, wait 5 seconds after turning off the computer before removing a component from the system board or disconnecting a device from the computer.
    1. Perform an orderly computer shutdown using the operating system menu.
    2. Turn off your computer and any devices connected to the computer.
    3. Ground yourself by touching an unpainted metal surface on the chassis, such as the metal around the card-slot openings at the back of the computer, before touching anything inside your computer.

    While you work, periodically touch an unpainted metal surface on the computer chassis to dissipate any static electricity that might harm internal components.

    1. Disconnect your computer and devices, including the monitor, from their electrical outlets. Also, disconnect any telephone or telecommunication lines from the computer.

    Doing so reduces the potential for personal injury or shock.

    In addition, take note of these safety guidelines when appropriate:

    • When you disconnect a cable, pull on its connector or on its strain-relief loop, not on the cable itself. Some cables have a connector with locking tabs; if you are disconnecting this type of cable, press in on the locking tabs before disconnecting the cable. As you pull connectors apart, keep them evenly aligned to avoid bending any connector pins. Also, before you connect a cable, ensure that both connectors are correctly oriented and aligned.
    • Handle components and cards with care. Do not touch the components or contacts on a card. Hold a card by its edges or by its metal mounting bracket. Hold a component such as a microprocessor chip by its edges, not by its pins.
      CAUTION: There is a danger of a new battery exploding if it is incorrectly installed. Replace the battery only with the same or equivalent type recommended by the manufacturer. Do not dispose of the battery along with household waste. Contact your local waste disposal agency for the address of the nearest battery deposit site.

    Protecting Against Electrostatic Discharge

    Static electricity can harm delicate components inside your computer. To prevent static damage, discharge static electricity from your body before you touch any of your computer's electronic components, such as the microprocessor. You can do so by touching an unpainted metal surface on the computer chassis.

    As you continue to work inside the computer, periodically touch an unpainted metal surface to remove any static charge your body may have accumulated.

    You can also take the following steps to prevent damage from electrostatic discharge (ESD):

    • Do not remove components from their antistatic packing material until you are ready to install the component in your computer. Just before unwrapping the antistatic packaging, discharge static electricity from your body.
    • When transporting an electrostatic sensitive component, first place it in an antistatic container or packaging.
    • Handle all electrostatic sensitive components in a static-safe area. If possible, use antistatic floor pads and workbench pads.

    Report Unresolved Customer Service Issues here

    I do not work for Dell. I too am a user.

    The forum is primarily user to user, with Dell employees moderating.