unable to contact DHCP server

Networking, Internet, Wireless

Networking, Internet, Wireless
From Wi-Fi to wired Ethernet, mobile broadband to modems: it's all spoken here.

unable to contact DHCP server

  • Hello,
     
    I cannot connect to the internet with my Inspiron 1100.  I have a Broadcom 440x 10/100 network card.
     
    I have installed the lastest driver for the card and I have tried to use both winsox fix & isp fix.
     
    When I do ipconfig /release and ipconfig /renew, I get an error message "unable to contact your DHCP server". 
     
    results of ipconfig /all as follows (by the way, is there an easier way to cut/paste from the cmd screen instead of retyping everything?):
     
    Windows IP Configuration
     
    Host Name: D75TBT21
    Primary DNS Suffix:
    Node Type: Hybrid
    IP Routing Enabled: No
    WINS Proxy Enabled: No
     
    Ethernet adapter Local Area Connection:
    Connection-specific DNS Suffix:
    Description: Broadcom 440x 10/100 Integrated Controller
    Physical Addres: 00-0B-DB-1E-E6-A0
    Dhcp Enable: Yes
    Autoconfiguration Enabled: Yes
    Autoconfiguration IP Address: 169.254.94.32
    Subnet Mask: 255.255.0.0
    IP Address: ?
    Default Gateway:
    DNS Servers:?
                           ?
                           ?
    Tunnel adapter Teredo Tunneling Pseudo-Interface:
    Connection-specific DNS Suffix:
    Description: Teredo Tunneling Pseudo-Interface
    Physical Address: FF-FF-FF-FF-FF-FF-FF-FF
    Dhcp Enabled: no
    IP Address: ?
    Default Gateway:
    NetBIOS over Tcpip: Disabled
     
    Thanks for any help you can provide.
  • Redirect to a text file

    IPCONFIG /ALL >My.txt

    [ The ">" symbol is what causes the text that normally goes to the video display to "redirect" to a text file instead. Because it is going to the file, you will not see it (at first) on the display, which will just remain black after your command. ]

    After you exit the CMD screen, you can run notepad (or wordpad) to open the "My.txt" and then copy and paste freely.

     

  • Follow this instruction ...

     

    Symptom

    DHCP Client Service may not automatically. When you attempt to start the Service manually, the following error may be displayed:

    Error: Could not start the DHCP Client Service on local computer

    Error 1068: The dependency service or group failed to start.

    Resolution

    The DHCP Client Service in Windows XP, depends on these three components:

    • AFD
    • NetBios over Tcpip
    • TCP/IP Protocol Driver

    If one of the above drivers fail to start, then the DHCP Client Service may not start.

    Step I - Make sure that the three driver files are present

    Open Windows Explorer and navigate to %Windir%\System32\Drivers folder. Make sure that the following files are present in the folder:

    • afd.sys
    • tcpip.sys
    • netbt.sys

    If one or more of the above driver files are missing, extract them from the Windows XP CD-ROM or from the ServicePackFiles\i386 folder, whichever is the latest version.

    Step II - Verify the number of Dependencies

    From other sources in the Web, I've found that some versions of Norton Antivirus (NAV) adds an entry to the DHCP Service Dependencies, and removing NAV does not remove the appropriate value from the DHCP Dependencies.

    To quickly determine the Dependency services for DHCP Client Service, type the following command in Start, Run dialog:

    CMD /K SC QC DHCP

    Verify the output. It should be exactly as below:

    [SC] GetServiceConfig SUCCESS

    SERVICE_NAME: dhcp
    TYPE : 20 WIN32_SHARE_PROCESS
    START_TYPE : 2 AUTO_START
    ERROR_CONTROL : 1 NORMAL
    BINARY_PATH_NAME : C:\WINDOWS\system32\svchost.exe -k netsvcs
    LOAD_ORDER_GROUP : TDI
    TAG : 0
    DISPLAY_NAME : DHCP Client
    DEPENDENCIES : Tcpip
    : Afd
    : NetBT
    SERVICE_START_NAME : LocalSystem

    If additional entries are listed under DEPENDENCIES...

    If any other additional drivers or Services are mentioned in the DEPENDENCIES section, you need to remove them via the registry. Follow these steps:

    • Click Start, Run and type Regedit.exe
    • Navigate to the following branch:
    • Backup the branch to a REG file

    HKEY_LOCAL_MACHINE \ SYSTEM \ CurrentControlSet \ Services \ Dhcp

    • Double-click DependOnService MULTI_SZ value and set it's data as follows:

    Tcpip
    Afd
    NetBT

    • Close Regedit.exe
    Step III - Verify that the Dependency Service / components are running

    Next step is to verify that the three dependency components are running. As the three components are actually the Kernel Drivers (Driver Service), you need to manage then via the Device Manager. Follow these steps:

    • Click Start, Run and type DEVMGMT.MSC
    • In the View menu, click Show hidden devices
    • Double-click Non-Plug and Play drivers section
    • Double-click the entry AFD, and click the Driver tab
    • Set the Startup type to System.
    • Start the service. Note down the error message if any.
    • Similarly start the two other drivers namely:
    • TCP/IP Protocol Driver
    • NetBios over Tcpip
    • Close Device Manager and restart Windows. [/quote]

    Message Edited by sbinh on 03-23-2006 07:44 PM

  • Thank you for the advice.

    I tried everything listed, but the 3 files were present in c:\windows\system32\drivers, the dependencies printed out exactly as you listed, and the components were all set to System startup and were already started when I looked at them in the device manager.  I appreciate the help and if anyone has any other suggestions, I would be very grateful.

    Thank you,

    Kimberly

  • I notice (reading back through) that it says WINS not enabled; however, I believe on our system we have selected DHCP over WINS, so then how could DHCP be running if not over WINS (and if WINS is not enabled, then would that not also prevent taking advantage of DHCP?)?
  • I'm not sure about this.  I checked the TCP/IP Advanced settings against the computer I am writing from, and they were the same.  There was no WINS address listed in either case.  When I did ipconfig /all on this computer, it also indicated that WINS was not enabled.

    A difference that I saw with this computer is that in the Local Area Connection Properties of the machine not working, I have choices for a Client Service for NetWare and related items (NW Link NetBIOS and NWLink IPX/SPX/NetBIOS Compatible Transport Protocol.  However, all 3 of these items are unchecked.

  • Personally I would remove all that Novell and IPX/SPX stuff. I believe the (only) client you need is Client for Windows

    At least that is all I / we use in Windows 2003 server "Domain" environment at my work place.