Just got a new Dell Inspiron N5050 laptop.
Using it about 3 weeks and loving it.
Pop up window invited me to update Windows. Clicked Yes.
While update was in progress, I accidently turned it off.
Now, It boots up, but moments afterward, it goes to Blue Screen of Death and, before I can even read the Blue Screen, it goes to Black Screen and asks how I would like to start up - Normal startup - Safe mode - Safe Mode with Prompts, etc.
So I want to restore it to an earlier time or just restore back to the beginning (factory settings).
Can I do this in one of the start up options on the Black Screen?
After switching on my laptop, Display shows following message.
A problem has been detected and windows has been shutdown to prevent damage to your computer.
If this is the first time you've seen this stop error screen, restart your computer.
If this screen appears again, follow these steps:
The BIOS in this system is not fully ACPI complaint, Please contact your system vender for an
***Stop:- 0X000000 A5 (0X000000X11,0X00000003,0X00000000,0X00000000)
My Laptop Model No: Inspiron 15 N5050
I buy recently two months back. why this problem happened, i don't know
Please advise, how to solve my problem
I am waiting for your prompt reply
Welcome to the Dell community. Thank you for providing the detailed description about the issue you are facing on the system. I would recommend you to follow these steps and the problem should be fixed
• Remove the battery and the adaptor from the system and hold the power button for 30 seconds and then turn on the system
• Run the hardware diagnostic by using a combination of ‘ Fn and power button ‘ or tap the F12 key on the dell logo screen and select diagnostics option. Observe and note any error code(s) or beep code(s) during the diagnostics
• You can click on the below mentioned link(s) to know how to do a system restore and factory restore on your system. Please keep in mind that doing a factory restore on the system will delete all your personal data and information on the system
For system restore: http://dell.to/u5wUkX
For factory restore: http://dell.to/gB7c4b
Please revert for assistance
Dell | Social Outreach Professional
Power it down by holding the power button down for 10 seconds. When powering up tap F8 repeatedly.
The advanced boot options should display.
Select Last Known Good Configuration. See if that works. This fixes such problems quite often.
Windows Reinstallation Guide and Related Wikies See here for other wikies such as Customising and Using Windows 8.1, Dell Wireless Cards and Unofficial Drivers.
Ok - Neither DELL-Sumer C's advice nor natakuc4's advice resolved the issue. When I ran the diagnostics (suggested by DELL-Sumer C), it said there are no issues detected.
I'm not a great geek, but you tech-savvy folks might understand what I'm about to explain:
My son said the issue is when Windows 7 boots uo and then attempts to use the hard drive as virtual ram - that's where the corruption lies. That's why running diagnostics indicates no problems - because that's not where the problem is.
According to my son, I need the restore software CD.
I didn't make one of my own when I got the lap top. I've only had it three weeks. I know, my bad. Can I get it from DELL?
In the US
First thing to try is last good known configuration and then a startup repair. Please see here.
my hard disk problem please tell me the solution
The error code is
You need a new, 2.5" 7- or 9.5 mm SATA notebook hard drive - yours has failed.
I recently updated to Windows 10 and it does not give me the option to repair your computer it says that windows did not load correctly please insert your windows disk and reboot I have tried but it is not working, I can not go in as safe mode, so I can save my files. I have tried going through windows 10 and reset my pc so I can Keep my files but it does not let me, I don't want to try the tab that says to remove everything until I save my files, please help thank u.
I did all the steps and i get this error code:200-0142 validation:42006 Msg: hard drive 0 - s/n s2tdj9bc104640 self test unsuccessful. status = 7 what do I do?? when I try to go to boot options the computer restart again
2000-0142 means the HDD has failed and needs replaced. You should use fedora to attempt data recovery as soon as possible:
Then you should get a SSD and clean install Windows 10 TH2: