I was doing some prep for Windows 8 upgrade.
I went into the Legacy BIOS settings and switched to UEFI (because my understanding is that allows Windows 8 to use Secure Boot feature).
On restart, the computer stopped with a message that said something like "no bootable device found". Anyone else have this issue?The BIOS version to A09.
This morning I deleted all of the partitions on my boot drive then changed my BIOS to UEFI mode. I only changed the one setting in the Bios. left the secure boot to disabled.
I rebooted and hit F12. I selected the UEFI DVD drive (legacy DVD drive was also listed) and booted to my Win 7 SP1 OS DVD. It installed fine on the unpartitioned hard drive and sure boots faster now. Still playing with it.
It appears that you have accidentally selected 'Legacy Mode' in BIOS. The default Boot Mode is set to UEFI and the operating system is installed in the UEFI Mode from the factory. The System will display the following error if the Operating System was installed in UEFI Mode and the Boot Mode has been changed to Legacy or Vice Versa.
To correct this error, please recheck and change the Boot Mode in the System Setup from Legacy to UEFI Mode. You may want to refer to the following steps to change the Boot Mode in System Setup to UEFI.- Restart / Power on your computer- At the first text on the screen or when the Dell logo appears, tap <F2> until the message Entering Setup appears- Boot Mode will be listed under Boot Select UEFI using the arrow keys to navigate and press enterSave and Exit the System Setup
Hope this helps. Do reply if you have any further questions. I would be glad to assist.
Thanks & Regards,Saurabh A#iworkfordellTo know more about Dell’s products, services and drivers & downloads, click Here. For helpful Dell Support Videos, you may click Here
This XPS 8500 is in Legacy mode, which is how it came to me. When I try to switch to UEFI, I got the error message saying "No boot device".
Thank you for a prompt response. Your computer is running with the latest BIOS version (A09) currently available. By design XPS 8500 is shipped from the factory with UEFI boot mode and the factory installed operating system is also installed in UEFI mode. Therefore I recommended you to recheck and retry switching between UEFI and legacy modes. Apart from this, you may also try to 'load BIOS factory defaults'. This will take the BIOS settings back to factory condition and will eliminate the confusion completely.
To load defaults, please follow the below mentioned steps:- Enter BIOS (By tapping F2 on start-up)- Tap < F9 > (You will be prompted with load defaults message)- Use arrow keys on keyboard to highlight < Yes > and tap < Enter >- Tap < F10 > to 'save' settings- Exit BIOS and recheck if the computer loads into 'Windows'
In either case, please re-enter in system BIOS and check the updated status of 'Boot Mode'.
Do reply if you have any further questions. I would be glad to assist.
This was a refurb system that I purchased last month. Perhaps that has something to do with why my system came with a different configuration? I will try as you suggest.
If you truly were in legacy mode you cannot just change it to UEFI and boot. you would have to reinstall windows.
Home Built Sandy Bridge P8P67 i7 2600k @ 4.5 GHz 8gigs GSkill Ripjaws. Corsair 800D Case and AX1200 Ps X-Fi Titanium Fatal1ty pro PCIe Sound CardDell Studio XPS 1645 Window 10 Pro
Forum member since 2003
I have an XPS 8500 that I am trying to fresh install Windows 8. My refurb system also came with Legacy option as default (that is the A09 default.) Upon setting it to UEFI and rebooting, it does not even recognize the bootable DVD in the drive - giving me the No Boot Drive found problem.
Is this something with the firmware? Is UEFI and secure boot support on the XPS 8500 with A09 firmware?
My XPS 8500 received on 10/23 also came set to "Legacy" and the manual indicates Legacy is the default.
UEFI only works with x64 OSes.
XPS 8500 definitely has 64bit OS because they have 8Gb of RAM or more. My theory is that whoever is re-imaging the refurb hard drives is using the wrong drive image.
Apparently, to install Windows 8 you need to boot in UEFI mode and the disc in which Windows is to be installed must be blank (without any partitions). See http://www.eightforums.com/tutorials/2328-uefi-unified-extensible-firmware-interface-install-windows-8-a.html.
You can definitely install Windows 8 without having a UEFI compatible BIOS because very few machines made before this year have that type of BIOS. You just don't get the features of Secure Boot, which I'm not sure what those are (except for "more better security").
Yes, I have success with a Windows 8 x64 bit install using Legacy. However, the PC will not boot from a Win8 DVD drive with UEFI enabled. It appears that the drives are not recognized when UEFI is enabled (not even DVD.)
If Windows was installed in legacy mode, another possibility to enable UEFI is to use the "Migrate to UEFI" Paragon tool, http://www.paragon-software.com/technologies/components/migrate-to-uefi/.
In this case, the Windows installation medium is not needed. Install a blank disc as second internal disc, boot in legacy mode and execute the process. When completed successfully, install the "migrated" disc as boot disc and boot in UEFI mode.